Thank you for choosing Soft Spaworld! This guide provides simple step-by-step instructions for installing your Soft Spa. Follow these steps carefully to ensure proper setup and optimal performance.
Before You Begin
Electrical Requirements
• Voltage: 220/240 Volt 10 Ampere (110/120 Volt 15 Ampere for USA/Canada)
• Outlet: Must be outdoor qualified and tested
• Important: Do NOT use extension cords
• Cable: 5m power cord included (if insufficient, consult a qualified electrician)
Location Requirements
• Choose a flat, level surface capable of supporting the spa weight
• Ensure proper drainage around the installation area
• Do NOT install in a glass house or cover with transparent plastic (risk of lens effect)
• Keep away from sprinklers and direct water sources
Installation Steps
Step 1: Unpack and Position
1. Carefully unpack the spa tub and Aqua Center
2. Place the spa tub in your desired location
3. Ensure the surface is completely level
4. Position the Aqua Center within 5 meters of the tub and electrical outlet
Step 2: Connect Tub and Aqua Center
1. Connect the tub to the Aqua Center using the provided pipes
2. Rotate the connections to tighten (no tools required)
3. Remove the red handle from the ball valve after connection is complete
4. Install the sponge silencer component over the connections
5. Cover the connections with the hose cover
Step 3: Fill the Spa
1. Fill the spa with clean water
2. Fill until water reaches the designated water level line inside the tub
3. Ensure all jets are covered with water
4. Check for any leaks around connections
Step 4: Electrical Connection
1. Plug the power cord into the designated electrical outlet
2. Ensure the plug fits tightly
3. Verify that the circuit breaker is functioning properly
Step 5: Initial Setup
1. Important: Do NOT power on until water level is correct
2. Turn on the main power switch
3. Set the date and time on the control panel
4. Select your preferred language (11 languages available)
Step 6: System Priming
1. Press the "Surfing Mode" button
2. Let it run for 5 minutes to expel air from the water pipes
3. This must be done before activating heating mode
Step 7: Heating Setup
1. After priming, set your desired temperature (recommended 38°C)
2. The heater will automatically start working
3. Allow 8-12 hours for initial heating (depending on ambient temperature)
Control Panel Operation
Basic Functions
• Temperature Display: Shows current and preset temperatures
• Pump Control: Press once for small water flow circulation
• Heating Mode: Toggle between Normal and ECO modes
• Lights: Control the LED color lighting system
• Air Switch: Adjust massage water flow intensity (3 levels)
WiFi and Bluetooth Setup
WiFi Connection
1. Download the app on your smartphone
2. Register and log in to the app
3. Enable location services on your phone
4. Connect your phone to a 2.4G WiFi network
5. On the control panel, press and hold "WiFi" for 5 seconds to clear previous connections
6. Press "WiFi" to switch to AP status
7. In the app, add a new SPA controller
8. Enter your WiFi network name and password
9. Connect your phone to the "adh" network when prompted
10. Return to the app to complete connection
Bluetooth Connection
1. Enable Bluetooth on your smartphone
2. Search for device named "YS-174"
3. Select and pair with the device
4. Enjoy Bluetooth music through the spa's waterproof speakers
Maintenance Tips
Water Chemistry
• Free Chlorine: 2-3 ppm
• pH Level: 7.2-7.8 (ideal 7.6)
• Total Alkalinity: 80-120 ppm
• Calcium Hardness: 50-150 ppm
• Test water after each use, minimum twice weekly
• Never use shock treatments or floating dispensers
Daily Maintenance
• Keep the lid closed when not in use
• Check water level regularly
• Clean the filter as needed
• Remove any debris from the water surface
Troubleshooting
Common Issues
• Power Problems: Check circuit breaker and power connection
• Heating Issues: Ensure proper water level and priming
• WiFi Connection: Verify 2.4G network and app settings
• Leaks: Check all connections and tighten if necessary
Warranty Information
Your Soft Spa comes with a 3-year warranty covering defects in materials and workmanship. To maintain warranty coverage:
• Follow all installation and maintenance instructions
• Keep water chemistry within recommended levels
• Do not alter or modify the spa
• Use only authorized parts and service